SHIS-115 Integrated Drill and Splitter

Home> SHIS-115 Integrated Drill and Splitter

SHIS-115 Integrated Drill and Splitter

A Bigger Hole, a Bigger Bite, One Excavator

Large rock jobs usually mean a long chain of steps: bring in a drill, make the holes, move the drill out, bring in the splitter. Each hand-off eats time and each extra machine adds cost. The SHIS-115 Integrated Drill and Splitter shortens that chain. It drills the hole and splits the rock from the same excavator, with no blasting involved.

It is the larger sibling of the SHIS-76, with a wider drilling diameter for heavier rock work. Here is what it offers and where it fits.

SMART integrated excavator drill and rock splitter

What Is the SHIS-115, Really?

Picture a rock drill and a hydraulic splitter built into one attachment and mounted on an excavator. The SHIS-115 Rock Splitter takes its power from the excavator's own hydraulics, and an added electro-hydraulic control system lets the operator switch between drilling and splitting. There is no separate drill to bring in, so the whole job can be done by one machine.

Why Crews Prefer It

  • Drill and splitter in one: no second machine needed
  • Fewer machine moves: less time lost between steps
  • Wide hole diameter: made for heavier rock work
  • Fast drilling and strong splitting force
  • Flexible reach: works on a face from different angles
  • Non-blasting: a safer choice near roads, buildings and people
Download Integrated Drill and Splitter Catalog
SHIS-115 Integrated Drill and Splitter

Key Specifications

SHIS-115 integrated drill and splitter specifications
Drilling diameter115 mm
Mountingexcavator attachment
Power sourceexcavator's hydraulic system
Controlelectro-hydraulic control system
Operationdrilling and splitting with one machine
Model rangeSHIS-76, SHIS-115, SHIS-130, SHIS-152

How the Machine Works

The operator positions the attachment and drills a 115 mm hole into the rock. Without changing machines, the wedge set then goes into the hole. Hydraulic pressure drives the centre wedge between two counter wedges, they press against the hole walls, and a crack opens along the line you marked. In short, the SHIS-115 Rock Drilling and Splitting Machine drills, splits and moves to the next hole, all from the cab.

A typical job goes like this:

  1. Position the excavator and mark the splitting line.
  2. Drill the first hole of 115 mm with the attachment.
  3. Switch to splitting and apply pressure until the rock opens.
  4. Move to the next hole and repeat.

A small planning habit helps: drill your holes towards a free face. The split pieces get room to move, and the break is cleaner.

Where You Can Use It

The SHIS-115 is made for hard rock work where blasting is not allowed or not safe. As a SHIS-115 Hydraulic Rock Splitter, it suits large quarry faces, deep trenches, foundation excavation and tunnel headings. It can reach a face from different angles, which helps on uneven ground and in cramped spots.

  • Quarry and open-pit excavation
  • Deep trenching and foundation work
  • Tunnel and shaft excavation
  • Highway and infrastructure rock cuts
  • Hard rock and large boulder removal
  • Concrete demolition

Why an Integrated Machine Makes Sense

When drilling and splitting are done by different machines, each one waits on the other. With one integrated unit, the excavator moves on to the next hole as soon as the last one is split. You spend less time idle, pay for fewer machines and need a smaller crew.

It also leaves more room on the site, which matters when space is tight.

Prepare Before You Begin

A little preparation saves a lot of time on site:

  • Walk the area and mark the splitting lines clearly
  • Plan the drilling pattern towards a free face
  • Check that the excavator is a suitable match for the attachment
  • Inspect hoses, couplings and drill parts before starting
  • Keep spare drill bits, hoses and couplings within reach

Safety and Maintenance

  • Keep people clear of the work area during drilling and splitting
  • Follow the recommended hole diameter and depth
  • Check hoses and couplings before every job
  • Wear goggles, gloves, a helmet and safety shoes on the ground crew
  • Clean the wedge set and drill parts after use and store them dry

Good habits keep the machine dependable, project after project.

Made to Run on Your Excavator

The attachment draws on the excavator's own hydraulics, so no separate power unit is needed. Used as an SHIS-115 Excavator Rock Splitter, it moves with the machine from hole to hole while the operator stays in the cab, well away from the rock.

Who Uses the SHIS-115?

  • Quarry and stone-cutting teams
  • Civil and construction contractors
  • Tunnel and micro-tunneling crews
  • Highway and infrastructure projects
  • Mining and excavation operations

Frequently Asked Questions

It drills holes and splits hard rock in one operation. Typical jobs include quarry work, deep trenching, foundations and tunnel excavation.

It drills holes of 115 mm diameter.

No. The drill and the splitter are combined in one unit, so that both steps are performed by the same excavator.

It uses the hydraulic power of the excavator, with an electro-hydraulic control system for drilling and splitting.

Yes. It’s a non-blasting method so it’s perfect for sites close to roads, buildings and other sensitive areas.

Yes. It can work at varying angles on a face, which is useful on uneven ground or confined sites.

Not much. A short briefing on the controls, drilling pattern and safety is usually enough to get started.

Conclusion

The SHIS-115 Integrated Drill and Splitter brings drilling and splitting together in one attachment, so a single excavator can handle heavy rock without blasting. Whether it is a quarry face, a deep trench or a tunnel heading, it saves time and keeps the job simple.

Contact Us